Niet beschikbaar voor verkoop
Frequency current converter with trip value KFD2-UFC-Ex1
- 1-channel
- Control circuit EEx ia IIC
- Input frequency 1 mHz ... 5 kHz
- Analog output 0/4 mA ... 20 mA
- Measuring range parameterisable
- 2 relay outputs
- 1 electronic output, isolated
- Each output can be assigned individual parameters, such as a trip value (high/low alarm), serially switched output, pulse divider or error message output
- Start-up override
- Restart inhibit
- Lead breakage (LB) and short-circuit (SC) monitoring
- Debounce filter
- Up to SIL 2 acc. to IEC 61508
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
De complete datasheet als PDF downloaden:
Technische gegevens KFD2-UFC-Ex1
| Productbeschrijving |
|---|
| 24 V DC |
| Supply | ||
|---|---|---|
| Connection | terminals 23+, 24- or power feed module/Power Rail | |
| Rated voltage | 20 ... 30 V DC | |
| Rated current | approx. 100 mA | |
| Power dissipation/power consumption | ≤ 2 W / 2.2 W | |
| Input | ||
| Connection | Input I: intrinsically safe: terminals 1+, 3- Input II: non-intrinsically safe: terminals 13+, 14- |
|
| Input I | acc. to EN 60947-5-6 (NAMUR), see manual for electrical data | |
| Pulse duration | > 50 µs | |
| Input frequency | 0.001 ... 5000 Hz | |
| Line fault detection | breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA | |
| Input II | startup override: 1 ... 1000 s, adjustable in steps of 1 s | |
| Active/Passive | I > 4 mA (for min. 100 ms) / I < 1.5 mA | |
| Open circuit voltage/short-circuit current | 18 V / 5 mA | |
| Output | ||
| Connection | Output I: terminals 10, 11, 12; Output II: terminals 16, 17, 18; Output III: terminals 19+, 20; Output IV: terminals 8+, 7-; |
|
| Output I, II | signal, relay | |
| Contact loading | 250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A | |
| Mechanical life | 5 x 107 switching cycles | |
| Energized/De-energized delay | approx. 20 ms / approx. 20 ms | |
| Output III | electronic output, passive | |
| Contact loading | 40 V DC | |
| Signal level | 1-signal: (L+) - 2.5 V (50 mA, short-circuit/overload proof) 0-signal: switched off (off-state current ≤ 10 µA) |
|
| Output IV | analog | |
| Current range | 0 ... 20 mA or 4 ... 20 mA | |
| Open loop voltage | max. 24 V DC | |
| Load | max. 650 Ω | |
| Fault signal | downscale I ≤ 3.6 mA , upscale ≥ 21.5 mA (acc. NAMUR NE43) | |
| Collective error message | Power Rail | |
| Transfer characteristics | ||
| Input I | ||
| Measurement range | 0.001 ... 5000 Hz | |
| Resolution | 0.1 % of the measurement value , ≥ 0.001 Hz | |
| Accuracy | 0.1 % of the measurement value , > 0.001 Hz | |
| Measuring time | < 100 ms | |
| Influence of ambient temperature | 0.003 %/K (30 ppm) | |
| Output I, II | ||
| Response delay | ≤ 200 ms | |
| Output IV | ||
| Resolution | < 10 µA | |
| Accuracy | < 20 µA | |
| Influence of ambient temperature | 0.005 %/K (50 ppm) | |
| Galvanic isolation | ||
| Output I, II/other circuits | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Mutual output I, II, III | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Output III, IV/power supply and collective error | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Output III/IV/Start-up override | functional insulation acc. to EN 50178, rated insulation voltage 300 Veff | |
| Start-up override/power supply and collective error | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Interface/power supply | reinforced insulation according to IEC 61140, rated insulation voltage 300 Veff | |
| Interface/output III | functional insulation acc. to EN 50178, rated insulation voltage 300 Veff | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 89/336/EEC | EN 61326, EN 50081-2, EN 50082-2 | |
| Low voltage | ||
| Directive 73/23/EEC | EN 50178 | |
| Conformity | ||
| Insulation coordination | EN 50178 | |
| Galvanic isolation | EN 50178 | |
| Electromagnetic compatibility | NE 21 | |
| Degree of protection | IEC 60529 | |
| Protection against electrical shock | IEC 61140 | |
| Input | EN 60947-5-6 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | 300 g | |
| Dimensions | 40 x 100 x 115 mm (1.6 x 3.9 x 4.5 inch) | |
| Height | 100 mm | |
| Width | 40 mm | |
| Length | 115 mm | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | TÜV 99 ATEX 1471 , for additional certificates see www.pepperl-fuchs.com | |
| Marking |  II (1)GD [EEx ia] IIC [circuit(s) in zone 0/1/2] |
|
| Supply | ||
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Input I | terminals 1+, 3- EEx ia IIC | |
| Voltage | 10.1 V | |
| Current | 13 mA | |
| Power | 34 mW (linear characteristic) | |
| Input II | terminals 13+, 14- non-intrinsically safe | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Output I, II | terminals 10, 11, 12; 16, 17, 18 non-intrinsically safe | |
| Maximum safe voltage | 253 V AC / 40 V DC (Attention! Um is no rated voltage.) | |
| Contact loading | 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 99 ATEX 1471) 50 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 02 ATEX 1885 X) |
|
| Output III | terminals 19+, 20- non-intrinsically safe | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Output IV | terminals 8+, 7- non-intrinsically safe | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Interface | RS 232 | |
| Maximum safe voltage | 40 V DC (Attention! Um is no rated voltage.) | |
| Certificate | TÜV 02 ATEX 1885 X , observe statement of conformity | |
| Marking | II 3G EEx nAC IIC T4 [device in zone 2] |
|
| Galvanic isolation | ||
| Input/Other circuits | safe galvanic isolation acc. to EN 50020, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 94/9/EC | EN 50014, EN 50020, EN 50021 | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210128 |
| ECLASS 12.0 | 27210128 |
| ECLASS 11.0 | 27210128 |
| ECLASS 10.0.1 | 27210128 |
| ECLASS 9.0 | 27210128 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC002918 |
| ETIM 8.0 | EC002918 |
| ETIM 7.0 | EC002918 |
| ETIM 6.0 | EC002918 |
| ETIM 5.0 | EC002475 |
| UNSPSC 12.1 | 39121007 |
Details: KFD2-UFC-Ex1
Product Documentation: KFD2-UFC-Ex1
| Manuals | Taal | Bestandstype | Bestandsgrootte |
|---|---|---|---|
| Manual | ENG | 1757 KB | |
| Manual | ENG | 3685 KB |
Approvals: KFD2-UFC-Ex1
| Certificates | Certificaatnummer | Taal | Bestandstype | Bestandsgrootte |
|---|---|---|---|---|
| Europe TUV Nord ATEX Category 3 G | TÜV 02 ATEX 1885X | ALL | 1101 KB | |
| exida Functional Safety Assessment | P+F 04/03-15 R016 | ALL | 337 KB |
Choose from various selection criteria like safety integrity level, performance level, device function, and signal type and find the SIL/PL assessed device that you are looking for.
Pepperl+Fuchs B.V.
Pettelaarpark 104
5216 PR 's-Hertogenbosch
Nederland
sales@nl.pepperl-fuchs.com
+31 73 75 07 107
sales-pa@nl.pepperl-fuchs.com
+31 73 75 07 108
© 2024 Alle rechten voorbehouden.
Pepperl+Fuchs is een toonaangevend ontwikkelaar en producent van elektronische sensoren en componenten voor de wereldwijde automatiseringsmarkt. Continue innovatie, hoge kwaliteit en gestage groei zijn de basis van ons succes, al meer dan 70 jaar. Pepperl+Fuchs heeft wereldwijd 6300 medewerkers en productiefaciliteiten in Duitsland, de Verenigde Staten, Singapore, Hongarije, Indonesië en Vietnam, waarvan het merendeel ISO 9001 gecertificeerd.